Off Your Rocker

LS roller rocker test

By Richard Holdener

Why on earth would anyone want to replace the factory rocker arms on an LS application? Aren’t they already roller rockers? Aren’t they already lightweight? Haven’t they been proven effective on countless thousands of high-powered LS applications? The answer to all of these questions is yes, including the first one.

Confused? Don’t be, as the factory roller rockers employed on every LS application offer a great many positive qualities, but rest assured, there is additional power to be had with the right rocker upgrade. As with any modification, replacing the factory rockers with roller rockers might take additional hardware, like pushrods or certainly valve springs, but when you go looking for power, leave no stone unturned.

To illustrate the gains offered by upgrading the factory rockers, we ran a back-to-back test using the stock rockers and a set of 1.72-ratio, aluminum roller rockers from COMP Cams. Before getting to the test results, let’s take a look at the test motor. Rather than run the test one of the many stock LS applications, we decided to compare the rockers on a more dedicated build up. Starting with an aluminum 5.7L block, we proceeded to stroke and poke the LS6 out to 383c.i.

The boys at L&R Automotive were responsible for the machining to accept the Speedmaster 4.0-inch stroker crank, JE forged pistons, and K1 connecting rods. Unlike stock pistons, the JE forgings featured valve reliefs to allow use of high-lift (long duration) cam profiles. In addition to the new rings and bearings, Fel Pro also came through with a new oil pump, timing chain, and MLS head gaskets.

Use of the 4.00-inch stroker crank meant it was necessary to shim and clearance the factory windage tray using washers and a small mallet. Minor machining on the bottom of the cylinder bore (for rod bolt clearance) was necessary with this stroker assembly. With a stout short block at the ready, it was time to make some power.

First on the To Do list was the proper camshaft. With power and drivability in mind, we selected an off-the-shelf grind from COMP Cams. Though we were running cathedral-port heads, we made our selection from the many rec-port offerings from COMP.

The 281LRR HR13 (pt# 54-461-11) featured a healthy .617/.624 lift split, a 231/247-degree duration split, and 113-degree lsa. COMP Cams also supplied a new set of hydraulic roller lifters (pt# 850-16), a set of Magnum pushrods (7.45 inches in length), and the required aluminum roller rockers for the test.

The combination of displacement and our power producers (heads, cam, and intake) combined to produce peak power numbers near 6,500 rpm. The high-lift cam allowed the engine to take full advantage of the flow offered by ported heads, while the duration figures made the sucker rev.

Working with the COMP cam was a set of 243 LS6 cylinder heads. To maximize the flow rate of the factory castings, the heads were shipped off to Total Engine Airflow (TEA) for their Stage 2 porting. The procedure included CNC porting of the intake, exhaust, and combustion chamber, revised valve sizing and a new spring package. The CNC procedure resulted in intake port volumes of 225cc.

When combined with the new 2.04-inch stainless steel valves and the CNC chamber work, the results were peak intake flow numbers of 328 cfm at just .600 lift. The exhaust flow was equally impressive through the new 1.57-inch valves, at 270 cfm. More than just peak numbers, the TEA Stage 2 package significantly improved the flow rate of the stock castings through the entire lift range, which is what really makes power.

The final touch on the TEA LS6 heads was a dual valve-spring package combined with titanium retainers. The springs offered enough seat and open pressure, coil-bind, and retainer-to-seal clearance to run cams with as much as .650 lift (perfect for our cam choice). The springs were also sufficient for use with the 1.72-ratio, aluminum roller rockers.

The final power producer employed on the aluminum stroker test motor was a 10mm, LSXRT composite intake manifold from FAST. To maximize flow to the motor, the intake was teamed with one of their massive 102mm Big-Mouth throttle bodies. The intake combo was fed by a set of billet fuel rails and 42-pound injectors, all from FAST. Finishing touches on the LS6 stroker included the factory coil packs, a FAST XFI/XIM management system, and a set of 1 7/8-inch stainless steel headers from American Racing (with 18-inch collector extensions).

Prior to start up, the pan was filled with 5W-30 Lucas Oil, and the motor was spun using the starter until oil pressure was visible on the gauge. Once started, the motor was treated to a pair of computer-controlled break-in cycles before running our rocker test. Equipped with the stock rockers, the 383 stroke produced repeatable runs of 578 hp at 6,500 rpm and 542 lb-ft of torque at 4,700 rpm.

After running the stock rockers, it was time to upgrade to the COMP units. For rockers, we chose a set of bolt-down, COMP Ultra-Gold Arc Series rockers (pt# 19024-16). The rockers offered ease of installation (simple bolt-down replacement), a 1.72:1 rocker ratio to slightly increase lift (stock LS was 1.7), and extra strong, CNC-extruded rocker bodies that featured billet trunnions with captured needle bearings. Toss in a roller tip to replace the friction-robbing, factory slider tip and you have the makings of a serious rocker upgrade.

The rocker swap was a simple bolt-down affair using the supplied rocker stands to replace the factory unit. Once installed, we ran the 383 stroker and were immediately rewarded with additional power. The roller rocker upgrade increased the peak power output to 588 hp at 6,400 rpm, but peak torque checked in at 541 lb-ft at 4,800 rpm.

The rockers offered additional power only above 5,300 rpm, with no change in the curve below that porting. It should be pointed out that the extra weight of the rockers will require sufficient spring pressure, but our TEA heads were already equipped for the test. If you are looking for more power, you might try getting off those stock rockers and going roller!

Sources:

American Racing Headers, americanracingheaders.com; COMP Cams, compcams.com; FAST, fuelairspark.com; JE Pistons, jepistons.com; K1, k1technologies.com; L&R Automotive; Speedmaster, speedmaster79.com; Total Engine Airflow, totalengineairflow.com; Total Seal Rings, totalseal.com

About the author

PPN Editor

Power & Performance News is the source for news, tech and products that help you get more performance from your vehicle. If powertrain performance projects and hardcore technical content are your interest, Power & Performance News is the publication designed for you. Our acclaimed editorial staff covers all aspects of engine and driveline upgrades with a mission of presenting information that is both interesting and achievable for the “average car guy”.
Read My Articles

Hot Rods and Muscle Cars in your inbox.

Build your own custom newsletter with the content you love from Street Muscle, directly to your inbox, absolutely FREE!

Free WordPress Themes
Street Muscle NEWSLETTER - SIGN UP FREE!

We will safeguard your e-mail and only send content you request.

Street Muscle - The Ultimate Muscle Car Magazine

streetmusclemag

We'll send you the most interesting Street Muscle articles, news, car features, and videos every week.

Street Muscle - The Ultimate Muscle Car Magazine

Street Muscle NEWSLETTER - SIGN UP FREE!

We will safeguard your e-mail and only send content you request.

Street Muscle - The Ultimate Muscle Car Magazine

streetmusclemag

Thank you for your subscription.

Subscribe to more FREE Online Magazines!

We think you might like...


fordmuscle
Classic Ford Performance
dragzine
Drag Racing
chevyhardcore
Classic Chevy Magazine

Street Muscle - The Ultimate Muscle Car Magazine

Thank you for your subscription.

Subscribe to more FREE Online Magazines!

We think you might like...

  • fordmuscle Classic Ford Performance
  • dragzine Drag Racing
  • chevyhardcore Classic Chevy Magazine

Street Muscle - The Ultimate Muscle Car Magazine

streetmusclemag

Thank you for your subscription.

Thank you for your subscription.

Street Muscle - The Ultimate Muscle Car Magazine

Thank you for your subscription.

Thank you for your subscription.

Loading